0
  • Over 46 million magnets in stock
  • Customer service in 3 languages
Shopping cart

Your shopping cart is empty.

No idea? Have another look at our bestsellers.

View our bestsellers

english deutsch français español italiano nederlands
The product was added to your shopping cart.
Go to shopping cart

Addicting table decoration

You just can't stop poking the ring!
Author: MD, Viersen, Germany
Online since: 03/03/2009, Number of visits: 589037
3
My table decoration consists of two pieces of wood. A ring magnet that is tied down on the bottom floats in between the two pieces. It's not hard to guess that there is also a magnet in the wood on top.
What's fascinating, though, is that the attraction works over such an unbelievable distance - in this case more than five centimetre!
Similar application from the deal lab Zahnfleiss in Eggenstein:

An approx. 8,5 g "floating tooth" was produced and used in a marketing campaign to win over new customers.
A ring magnet (R-10-04-05-G) is embedded in the tooth. On the top and the bottom of the frame disc magnets (S-20-10-N) are embedded, which make the tooth float.
If you have this object on your desk, you'll always feel compelled to make the ring wobble... (see video)
It is visually impressive when the top wood is just slightly bigger than the magnet inside. This way, the magnet appears smaller and the large distance impresses even more.

Material needed:

  • 2 disc magnets S-20-10-N
  • 1 ring magnet R-10-04-05-G
  • a plywood board of 18 mm thickness
  • a round wood stick
  • wood glue
  • a piece of transparent thread
  • a wire hook
First, use a 20 mm drill to drill a hole for the disc magnet into the plywood.
I made three of them at once, but one is fine too.
In order to get the bottom wood to 2 - 3 mm thickness, you can deepen the hole with a router.
Place the magnet tentatively in the hole. Then, take it out again and fine down the wood until the magnet is flush with the wood.
Roughly cut the wood.
Cut a thin piece of wood at the same length and width as the top.
Countersink the magnet in the hole and then glue the top on it.
Let it dry well.
Place a second disc magnet on the wood and mark the position of the magnet inside the wood with a pencil.
Saw off the wood close to the magnet on both sides, but leave about 2 -3 mm wood to the left and the right. Watch out for the attraction between magnet and circular saw blades.
Sand down the wood on all sides.
The disc magnet is at the bottom of the left piece of wood.
The disc magnet is at the bottom of the left piece of wood.
Prepare a similar piece of wood for the base. Drill about 1 cm deep holes into the base and the top wood for the round wood stick.
The distance between the wood pieces should be about 11 cm. At this distance, the ring magnet can float around the center.
Cut the round wood stick at the appropriate length and sand it down.
Put a little bit of wood glue in the holes and put the round wood stick in them.
Let it dry well.
Push the wire hook into the base, tie the thread to the ring magnet and then tie it at a height where the ring still steadily gravitates towards the disc magnet.

Articles used

Load...
R-10-04-05-G Ring magnet Ø 10/4 mm, height 5 mm, holds approx. 2,5 kg, neodymium, N42, gold-plated
R-10-04-05-G
Ring magnet Ø 10/4 mm, height 5 mm, holds approx. 2,5 kg, neodymium, N42, gold-plated
R-10-04-05-G Ring magnet Ø 10/4 mm, height 5 mm, holds approx. 2,5 kg, neodymium, N42, gold-plated
5 pcs. 1,13 EUR ea.*
from 15 pcs. 0,99 EUR ea.*
from 40 pcs. 0,88 EUR ea.*
from 80 pcs. 0,81 EUR ea.*
Ask for a rebate from 550 pcs.
Available: 12 375 pcs.
Bestseller icon S-20-10-N Disc magnet Ø 20 mm, height 10 mm, holds approx. 11 kg, neodymium, N42, nickel-plated
S-20-10-N
Disc magnet Ø 20 mm, height 10 mm, holds approx. 11 kg, neodymium, N42, nickel-plated
Bestseller icon S-20-10-N Disc magnet Ø 20 mm, height 10 mm, holds approx. 11 kg, neodymium, N42, nickel-plated
1 pc. 4,75 EUR ea.*
from 3 pcs. 4,15 EUR ea.*
from 10 pcs. 3,61 EUR ea.*
from 20 pcs. 3,35 EUR ea.*
from 40 pcs. 3,12 EUR ea.*
Ask for a rebate from 180 pcs.
Available: 40 000 pcs.
Bestseller icon R-10-04-05-N Ring magnet Ø 10/4 mm, height 5 mm, holds approx. 2,5 kg, neodymium, N42, nickel-plated
R-10-04-05-N
Ring magnet Ø 10/4 mm, height 5 mm, holds approx. 2,5 kg, neodymium, N42, nickel-plated
Bestseller icon R-10-04-05-N Ring magnet Ø 10/4 mm, height 5 mm, holds approx. 2,5 kg, neodymium, N42, nickel-plated
5 pcs. 0,93 EUR ea.*
from 15 pcs. 0,81 EUR ea.*
from 40 pcs. 0,72 EUR ea.*
from 80 pcs. 0,66 EUR ea.*
Ask for a rebate from 650 pcs.
Available: 46 645 pcs.
3 people like this customer project
-Projects are bookmarked in your customer account

This might also interest you

Levitating rod magnet Levitating rod magnet
Vacation Home for Rats Vacation Home for Rats
Chess and chequerboard with magnetic game pieces Chess and chequerboard with magnetic game pieces
Flag holder for the balcony Flag holder for the balcony

keywords

The entire content of this site is protected by copyright.
Copying the content or using it elsewhere is not permitted without explicit approval.